{"id":534646,"date":"2026-07-17T17:52:54","date_gmt":"2026-07-17T21:52:54","guid":{"rendered":"https:\/\/www.fs1inc.com\/blog\/?p=534646"},"modified":"2026-07-19T12:24:21","modified_gmt":"2026-07-19T16:24:21","slug":"2001-pontiac-grand-am-pcm-replacement-guide","status":"publish","type":"post","link":"https:\/\/www.fs1inc.com\/blog\/2001-pontiac-grand-am-pcm-replacement-guide\/","title":{"rendered":"2001 Pontiac Grand Am 2.4L PCM Replacement and Programming"},"content":{"rendered":"<div class=\"container\">\n<section class=\"hero\">\n<div class=\"code-badge\">PCM<\/div>\n<h1>2001 Pontiac Grand Am 2.4L PCM Replacement and Programming<\/h1>\n<p class=\"hero-subtitle\">In the 2001 Pontiac Grand Am 2.4L, the powertrain control module (PCM) is the control center of the fuel injection system, located under the instrument panel. Failure often results from internal component faults, leading to drivability issues, communication loss, and stored trouble codes.<\/p>\n<\/section>\n<div class=\"quick-summary\">\n<h2>Quick Summary<\/h2>\n<ul>\n<li>The PCM is located under the instrument panel and requires 0.9 hours of labor for removal and replacement.<\/li>\n<li>A relearn procedure, taking 0.5 hours, is necessary after installing a new or replacement PCM.<\/li>\n<li>Factory cautions state that programming should only be performed when directed by a service procedure or GM bulletin.<\/li>\n<li>Two service bulletins address communication freeze-frame issues and transmission flare\/upshift problems that may require PCM reprogramming.<\/li>\n<li>Internal trouble codes such as P0601 through P0607 and several P16xx codes indicate PCM hardware or communication faults.<\/li>\n<\/ul>\n<\/div>\n<div class=\"info-section\">\n<p>If your 2001 Pontiac Grand Am with the 2.4L engine is experiencing drivability problems, transmission shifting issues, or a check engine light, the powertrain control module (PCM) may be at fault. The PCM manages fuel injection, ignition timing, and transmission operation, making it a critical component. This guide explains what the PCM does, where it is located, how replacement is performed, and what programming steps are required afterward. You will also learn about common symptoms, relevant factory service bulletins, and how to protect the module from future failure.<\/p>\n<\/div>\n<div class=\"info-section\">\n<h2>What the PCM Does in a 2001 Pontiac Grand Am<\/h2>\n<p>The powertrain control module in your 2001 Pontiac Grand Am 2.4L acts as the brain of the engine management system. It receives input from sensors such as the oxygen sensor, throttle position sensor, and crankshaft position sensor, then adjusts fuel delivery and spark timing to maintain proper performance and emissions. The PCM also controls the automatic transmission shift points and torque converter lockup. When the module fails, it can cause a wide range of issues from no-start conditions to erratic shifting. For this vehicle, <a href=\"https:\/\/www.fs1inc.com\/gm\/pontiac-pcm-ecm-ecu-engine-computer\/grand-am-engine-computers.html\">replacement PCMs for the Grand Am<\/a> are available that match the original specifications, ensuring plug-and-play compatibility after proper programming.<\/p>\n<\/div>\n<div class=\"info-section\">\n<h2>Where the PCM Is Located and What Replacement Involves<\/h2>\n<p>The PCM on the 2001 Pontiac Grand Am 2.4L is mounted under the instrument panel, typically on the passenger side near the kick panel or behind the glove box. Access may require removing a trim panel or the glove box assembly. According to labor time guidelines, removing and replacing the PCM takes approximately 0.9 hours. After installation, a PCM relearn procedure is required, which adds about 0.5 hours of labor. The relearn allows the module to adapt to the vehicle&#8217;s specific sensor inputs and idle characteristics. Ensure the battery is disconnected before handling the module to avoid electrical damage.<\/p>\n<figure style=\"margin:22px auto;text-align:center;max-width:720px\"><img decoding=\"async\" style=\"max-width:100%;height:auto;border:1px solid #e2e6ec;border-radius:8px\" src=\"https:\/\/www.fs1inc.com\/blog\/wp-content\/uploads\/2026\/07\/2001-pontiac-grand-am-pcm-location-card.webp\" alt=\"2001 Pontiac Grand Am PCM location diagram\" loading=\"lazy\"\/><figcaption style=\"font-size:13px;color:#667085;margin-top:8px\">Typical PCM mounting area on the 2001 Pontiac Grand Am (reference).<\/figcaption><\/figure>\n<div style=\"background:#f7f9fc;border:1px solid #e2e8f2;border-radius:10px;padding:18px 24px;margin:18px 0\">\n<h3 style='margin-top:0'>How to Reach the PCM on the 2001 Pontiac Grand Am<\/h3>\n<ol style=\"margin:14px 0 6px 0;padding-left:26px\">\n<li style=\"margin:10px 0;line-height:1.65\"><b>Disconnect<\/b> the negative battery cable.<\/li>\n<li style=\"margin:10px 0;line-height:1.65\"><b>Remove<\/b> the left closeout\/insulator panel.<\/li>\n<li style=\"margin:10px 0;line-height:1.65\"><b>Loosen<\/b> the powertrain control module (PCM) connector.<\/li>\n<li style=\"margin:10px 0;line-height:1.65\"><b>Disconnect<\/b> the PCM electrical connectors.<\/li>\n<li style=\"margin:10px 0;line-height:1.65\"><b>Slide<\/b> the PCM from the PCM bracket.<\/li>\n<li style=\"margin:10px 0;line-height:1.65\"><b>Remove<\/b> the new PCM from the packaging and inspect the service.<\/li>\n<li style=\"margin:10px 0;line-height:1.65\"><b>Slide<\/b> the PCM into the PCM bracket.<\/li>\n<li style=\"margin:10px 0;line-height:1.65\"><b>Position<\/b> system variation learn procedure must be performed.<\/li>\n<\/ol>\n<p style='margin:10px 0 0 0'><em>Work with the ignition off, and treat the module as static-sensitive: avoid touching the connector pins at any point.<\/em><\/p>\n<\/div>\n<table style=\"width:100%;border-collapse:collapse;margin:18px 0;font-size:15px\">\n<tr>\n<th style=\"border:1px solid #d6dbe3;background:#f2f5f9;padding:9px 12px;text-align:left\">Operation<\/th>\n<th style=\"border:1px solid #d6dbe3;background:#f2f5f9;padding:9px 12px;text-align:left\">Configuration<\/th>\n<th style=\"border:1px solid #d6dbe3;background:#f2f5f9;padding:9px 12px;text-align:left\">Book Time<\/th>\n<\/tr>\n<tr>\n<td style=\"border:1px solid #d6dbe3;padding:9px 12px\">Engine Control Module R&amp;R<\/td>\n<td style=\"border:1px solid #d6dbe3;padding:9px 12px\">All configurations<\/td>\n<td style=\"border:1px solid #d6dbe3;padding:9px 12px\">0.9 hr<\/td>\n<\/tr>\n<tr>\n<td style=\"border:1px solid #d6dbe3;padding:9px 12px\">Engine Control Module Relearn<\/td>\n<td style=\"border:1px solid #d6dbe3;padding:9px 12px\">All configurations<\/td>\n<td style=\"border:1px solid #d6dbe3;padding:9px 12px\">0.5 hr<\/td>\n<\/tr>\n<tr>\n<td style=\"border:1px solid #d6dbe3;padding:9px 12px\">Powertrain Control Module Relearn<\/td>\n<td style=\"border:1px solid #d6dbe3;padding:9px 12px\">All configurations<\/td>\n<td style=\"border:1px solid #d6dbe3;padding:9px 12px\">0.5 hr<\/td>\n<\/tr>\n<tr>\n<td style=\"border:1px solid #d6dbe3;padding:9px 12px\">Powertrain Control Module R&amp;R<\/td>\n<td style=\"border:1px solid #d6dbe3;padding:9px 12px\">All configurations<\/td>\n<td style=\"border:1px solid #d6dbe3;padding:9px 12px\">0.9 hr<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<div class=\"info-section\">\n<h2>Programming Requirements After Replacement<\/h2>\n<p>Factory procedure for a new PCM on this vehicle involves using a Tech 2 scan tool to select &#8216;Reprogram ECU&#8217; and then choosing &#8216;Off-Board Programming Adapter&#8217; as the ECU location. The Off-Board Programming method is used when the vehicle is not present. GM cautions that programming should only be performed when directed by a service procedure or a GM service bulletin, and the ignition must not be turned off if the process is interrupted. All PCM and DLC connections must be secure, and the Techline software must be up to date. Flagship One provides <a href=\"https:\/\/www.fs1inc.com\/2001-pontiac-grand-am-2-4l-engine-computer-pcm-ecm-ecu-programmed-plug-play.html\">a VIN-programmed replacement unit<\/a> that arrives with the correct calibration already loaded, so the post-install programming step is already completed for you.<\/p>\n<\/div>\n<div class=\"info-section\">\n<h2>Symptoms of a Failing PCM<\/h2>\n<p>A failing PCM in the 2001 Pontiac Grand Am 2.4L can produce a variety of symptoms. The engine may crank but not start, or it may stall unexpectedly while driving. Misfire codes and rough idle are common. Scan tool communication may be lost entirely, preventing diagnosis. Transmission issues such as neutral flare, RPM flare while in drive, or a lack of 1-2 upshift have been reported, often accompanied by a Service Engine Soon light. One internal fault that may appear is <a href=\"https:\/\/www.fs1inc.com\/blog\/dtc-p0601-internal-control-module-memory-checksum-error\/\">internal control module fault P0601<\/a>, which indicates a checksum error in the PCM&#8217;s memory. Other drivability complaints include poor fuel economy and hesitation under acceleration.<\/p>\n<\/div>\n<div class=\"info-section\">\n<h2>Module Trouble Codes on the 2001 Pontiac Grand Am<\/h2>\n<p>The following diagnostic trouble codes are internal to the PCM and indicate hardware or software faults within the module itself. These codes are not related to external sensors or circuits and typically require PCM replacement or reprogramming to resolve.<\/p>\n<table style=\"width:100%;border-collapse:collapse;margin:18px 0;font-size:15px\">\n<tr>\n<th style=\"border:1px solid #d6dbe3;background:#f2f5f9;padding:9px 12px;text-align:left\">Code<\/th>\n<th style=\"border:1px solid #d6dbe3;background:#f2f5f9;padding:9px 12px;text-align:left\">Meaning<\/th>\n<th style=\"border:1px solid #d6dbe3;background:#f2f5f9;padding:9px 12px;text-align:left\">Full Guide<\/th>\n<\/tr>\n<tr>\n<td style=\"border:1px solid #d6dbe3;padding:9px 12px\"><a href=\"https:\/\/www.fs1inc.com\/blog\/dtc-p0601-internal-control-module-memory-checksum-error\/\" style=\"color:#0563C1;text-decoration:none;display:block;cursor:pointer\"><b>P0601<\/b><\/a><\/td>\n<td style=\"border:1px solid #d6dbe3;padding:9px 12px\"><a href=\"https:\/\/www.fs1inc.com\/blog\/dtc-p0601-internal-control-module-memory-checksum-error\/\" style=\"color:#1a2b49;text-decoration:none;display:block;cursor:pointer\">Internal memory checksum error<\/a><\/td>\n<td style=\"border:1px solid #d6dbe3;padding:9px 12px\"><a href=\"https:\/\/www.fs1inc.com\/blog\/dtc-p0601-internal-control-module-memory-checksum-error\/\" style=\"color:#0563C1\"><b><u>Full P0601 guide &rarr;<\/u><\/b><\/a><\/td>\n<\/tr>\n<tr>\n<td style=\"border:1px solid #d6dbe3;padding:9px 12px\"><a href=\"https:\/\/www.fs1inc.com\/blog\/dtc-p0602-control-module-programming-error\/\" style=\"color:#0563C1;text-decoration:none;display:block;cursor:pointer\"><b>P0602<\/b><\/a><\/td>\n<td style=\"border:1px solid #d6dbe3;padding:9px 12px\"><a href=\"https:\/\/www.fs1inc.com\/blog\/dtc-p0602-control-module-programming-error\/\" style=\"color:#1a2b49;text-decoration:none;display:block;cursor:pointer\">Control module programming error<\/a><\/td>\n<td style=\"border:1px solid #d6dbe3;padding:9px 12px\"><a href=\"https:\/\/www.fs1inc.com\/blog\/dtc-p0602-control-module-programming-error\/\" style=\"color:#0563C1\"><b><u>Full P0602 guide &rarr;<\/u><\/b><\/a><\/td>\n<\/tr>\n<tr>\n<td style=\"border:1px solid #d6dbe3;padding:9px 12px\"><a href=\"https:\/\/www.fs1inc.com\/blog\/dtc-p0603-internal-control-module-keep-alive-memory-kam-error\/\" style=\"color:#0563C1;text-decoration:none;display:block;cursor:pointer\"><b>P0603<\/b><\/a><\/td>\n<td style=\"border:1px solid #d6dbe3;padding:9px 12px\"><a href=\"https:\/\/www.fs1inc.com\/blog\/dtc-p0603-internal-control-module-keep-alive-memory-kam-error\/\" style=\"color:#1a2b49;text-decoration:none;display:block;cursor:pointer\">Keep-alive memory (KAM) error<\/a><\/td>\n<td style=\"border:1px solid #d6dbe3;padding:9px 12px\"><a href=\"https:\/\/www.fs1inc.com\/blog\/dtc-p0603-internal-control-module-keep-alive-memory-kam-error\/\" style=\"color:#0563C1\"><b><u>Full P0603 guide &rarr;<\/u><\/b><\/a><\/td>\n<\/tr>\n<tr>\n<td style=\"border:1px solid #d6dbe3;padding:9px 12px\"><a href=\"https:\/\/www.fs1inc.com\/blog\/dtc-p0604-internal-control-module-random-access-memory-ram-error\/\" style=\"color:#0563C1;text-decoration:none;display:block;cursor:pointer\"><b>P0604<\/b><\/a><\/td>\n<td style=\"border:1px solid #d6dbe3;padding:9px 12px\"><a href=\"https:\/\/www.fs1inc.com\/blog\/dtc-p0604-internal-control-module-random-access-memory-ram-error\/\" style=\"color:#1a2b49;text-decoration:none;display:block;cursor:pointer\">Internal RAM error<\/a><\/td>\n<td style=\"border:1px solid #d6dbe3;padding:9px 12px\"><a href=\"https:\/\/www.fs1inc.com\/blog\/dtc-p0604-internal-control-module-random-access-memory-ram-error\/\" style=\"color:#0563C1\"><b><u>Full P0604 guide &rarr;<\/u><\/b><\/a><\/td>\n<\/tr>\n<tr>\n<td style=\"border:1px solid #d6dbe3;padding:9px 12px\"><a href=\"https:\/\/www.fs1inc.com\/blog\/dtc-p0605-internal-control-module-read-only-memory-rom-error\/\" style=\"color:#0563C1;text-decoration:none;display:block;cursor:pointer\"><b>P0605<\/b><\/a><\/td>\n<td style=\"border:1px solid #d6dbe3;padding:9px 12px\"><a href=\"https:\/\/www.fs1inc.com\/blog\/dtc-p0605-internal-control-module-read-only-memory-rom-error\/\" style=\"color:#1a2b49;text-decoration:none;display:block;cursor:pointer\">Internal ROM error<\/a><\/td>\n<td style=\"border:1px solid #d6dbe3;padding:9px 12px\"><a href=\"https:\/\/www.fs1inc.com\/blog\/dtc-p0605-internal-control-module-read-only-memory-rom-error\/\" style=\"color:#0563C1\"><b><u>Full P0605 guide &rarr;<\/u><\/b><\/a><\/td>\n<\/tr>\n<tr>\n<td style=\"border:1px solid #d6dbe3;padding:9px 12px\"><a href=\"https:\/\/www.fs1inc.com\/blog\/dtc-p0606-control-module-processor\/\" style=\"color:#0563C1;text-decoration:none;display:block;cursor:pointer\"><b>P0606<\/b><\/a><\/td>\n<td style=\"border:1px solid #d6dbe3;padding:9px 12px\"><a href=\"https:\/\/www.fs1inc.com\/blog\/dtc-p0606-control-module-processor\/\" style=\"color:#1a2b49;text-decoration:none;display:block;cursor:pointer\">Module processor failure<\/a><\/td>\n<td style=\"border:1px solid #d6dbe3;padding:9px 12px\"><a href=\"https:\/\/www.fs1inc.com\/blog\/dtc-p0606-control-module-processor\/\" style=\"color:#0563C1\"><b><u>Full P0606 guide &rarr;<\/u><\/b><\/a><\/td>\n<\/tr>\n<tr>\n<td style=\"border:1px solid #d6dbe3;padding:9px 12px\"><a href=\"https:\/\/www.fs1inc.com\/blog\/dtc-p0607-control-module-performance\/\" style=\"color:#0563C1;text-decoration:none;display:block;cursor:pointer\"><b>P0607<\/b><\/a><\/td>\n<td style=\"border:1px solid #d6dbe3;padding:9px 12px\"><a href=\"https:\/\/www.fs1inc.com\/blog\/dtc-p0607-control-module-performance\/\" style=\"color:#1a2b49;text-decoration:none;display:block;cursor:pointer\">Module performance fault<\/a><\/td>\n<td style=\"border:1px solid #d6dbe3;padding:9px 12px\"><a href=\"https:\/\/www.fs1inc.com\/blog\/dtc-p0607-control-module-performance\/\" style=\"color:#0563C1\"><b><u>Full P0607 guide &rarr;<\/u><\/b><\/a><\/td>\n<\/tr>\n<tr>\n<td style=\"border:1px solid #d6dbe3;padding:9px 12px\"><a href=\"https:\/\/www.fs1inc.com\/blog\/dtc-p1600-pcm-battery-voltage-supply-loss-of-communication\/\" style=\"color:#0563C1;text-decoration:none;display:block;cursor:pointer\"><b>P1600<\/b><\/a><\/td>\n<td style=\"border:1px solid #d6dbe3;padding:9px 12px\"><a href=\"https:\/\/www.fs1inc.com\/blog\/dtc-p1600-pcm-battery-voltage-supply-loss-of-communication\/\" style=\"color:#1a2b49;text-decoration:none;display:block;cursor:pointer\">Loss of communication \/ battery voltage supply fault<\/a><\/td>\n<td style=\"border:1px solid #d6dbe3;padding:9px 12px\"><a href=\"https:\/\/www.fs1inc.com\/blog\/dtc-p1600-pcm-battery-voltage-supply-loss-of-communication\/\" style=\"color:#0563C1\"><b><u>Full P1600 guide &rarr;<\/u><\/b><\/a><\/td>\n<\/tr>\n<tr>\n<td style=\"border:1px solid #d6dbe3;padding:9px 12px\"><a href=\"https:\/\/www.fs1inc.com\/blog\/dtc-p1621-control-module-long-term-memory-performance\/\" style=\"color:#0563C1;text-decoration:none;display:block;cursor:pointer\"><b>P1621<\/b><\/a><\/td>\n<td style=\"border:1px solid #d6dbe3;padding:9px 12px\"><a href=\"https:\/\/www.fs1inc.com\/blog\/dtc-p1621-control-module-long-term-memory-performance\/\" style=\"color:#1a2b49;text-decoration:none;display:block;cursor:pointer\">Control module long-term memory performance<\/a><\/td>\n<td style=\"border:1px solid #d6dbe3;padding:9px 12px\"><a href=\"https:\/\/www.fs1inc.com\/blog\/dtc-p1621-control-module-long-term-memory-performance\/\" style=\"color:#0563C1\"><b><u>Full P1621 guide &rarr;<\/u><\/b><\/a><\/td>\n<\/tr>\n<tr>\n<td style=\"border:1px solid #d6dbe3;padding:9px 12px\"><b>P1626<\/b><\/td>\n<td style=\"border:1px solid #d6dbe3;padding:9px 12px\">Module-internal fault<\/td>\n<td style=\"border:1px solid #d6dbe3;padding:9px 12px\">&mdash;<\/td>\n<\/tr>\n<tr>\n<td style=\"border:1px solid #d6dbe3;padding:9px 12px\"><a href=\"https:\/\/www.fs1inc.com\/blog\/dtc-p1627-control-module-a-d-performance\/\" style=\"color:#0563C1;text-decoration:none;display:block;cursor:pointer\"><b>P1627<\/b><\/a><\/td>\n<td style=\"border:1px solid #d6dbe3;padding:9px 12px\"><a href=\"https:\/\/www.fs1inc.com\/blog\/dtc-p1627-control-module-a-d-performance\/\" style=\"color:#1a2b49;text-decoration:none;display:block;cursor:pointer\">A\/D performance fault<\/a><\/td>\n<td style=\"border:1px solid #d6dbe3;padding:9px 12px\"><a href=\"https:\/\/www.fs1inc.com\/blog\/dtc-p1627-control-module-a-d-performance\/\" style=\"color:#0563C1\"><b><u>Full P1627 guide &rarr;<\/u><\/b><\/a><\/td>\n<\/tr>\n<tr>\n<td style=\"border:1px solid #d6dbe3;padding:9px 12px\"><b>P1630<\/b><\/td>\n<td style=\"border:1px solid #d6dbe3;padding:9px 12px\">Module-internal fault<\/td>\n<td style=\"border:1px solid #d6dbe3;padding:9px 12px\">&mdash;<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<div class=\"info-section\">\n<h2>Factory Service Bulletins Worth Knowing<\/h2>\n<p>Two factory service bulletins apply to the 2001 Pontiac Grand Am 2.4L PCM. Bulletin #04-06-04-024 addresses a condition where the PCM will not properly communicate on-board diagnostic freeze frame information to non-Tech 2 service equipment, requiring a PCM reprogram. Bulletin #03-07-30-021A covers neutral flare, RPM flare while in drive, no 1-2 upshift, and SES light illumination with DTCs P1810 or P1815 set; the remedy is to reprogram the PCM. A third bulletin, #02-06-04-057E, provides labor operation assignments for all control module reprogramming under warranty.<\/p>\n<table style=\"width:100%;border-collapse:collapse;margin:18px 0;font-size:15px\">\n<tr>\n<th style=\"border:1px solid #d6dbe3;background:#f2f5f9;padding:9px 12px;text-align:left\">Bulletin<\/th>\n<th style=\"border:1px solid #d6dbe3;background:#f2f5f9;padding:9px 12px;text-align:left\">Subject<\/th>\n<th style=\"border:1px solid #d6dbe3;background:#f2f5f9;padding:9px 12px;text-align:left\">What It Addresses<\/th>\n<\/tr>\n<tr>\n<td style=\"border:1px solid #d6dbe3;padding:9px 12px\"><b>04-06-04-024<\/b><\/td>\n<td style=\"border:1px solid #d6dbe3;padding:9px 12px\">Powertrain Control Module (PCM) Will Not Properly Communicate On-Board Diagnostic Freeze Frame <\/td>\n<td style=\"border:1px solid #d6dbe3;padding:9px 12px\">Some customers may comment that their vehicle&#8217;s engine is unable to be properly serviced or tested using non-TECH2\u00ae (Generic) service or test equipment. When\u2026<\/td>\n<\/tr>\n<tr>\n<td style=\"border:1px solid #d6dbe3;padding:9px 12px\"><b>03-07-30-021<\/b><\/td>\n<td style=\"border:1px solid #d6dbe3;padding:9px 12px\">Neutral Flare and\/or RPM Flare While In Drive, No 1-2 Upshift, Service Engine Soon (SES) Light <\/td>\n<td style=\"border:1px solid #d6dbe3;padding:9px 12px\">Some customers may comment on a neutral flare and\/or RPM increase while in drive or no 1\u20132 upshift and\/or the Service Engine Soon (SES) telltale may be\u2026<\/td>\n<\/tr>\n<tr>\n<td style=\"border:1px solid #d6dbe3;padding:9px 12px\"><b>02-06-04-057<\/b><\/td>\n<td style=\"border:1px solid #d6dbe3;padding:9px 12px\">Warranty Admin. &#8211; Labor Operation Assignments for All Control Module Reprogramming &#8211; (Mar 2, 20<\/td>\n<td style=\"border:1px solid #d6dbe3;padding:9px 12px\">&mdash;<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<div class=\"info-section\">\n<h2>Protecting the PCM in Your 2001 Pontiac Grand Am<\/h2>\n<ul style=\"margin:14px 0 6px 0;padding-left:26px\">\n<li style=\"margin:10px 0;line-height:1.65\">Maintain the charging system in good condition; voltage spikes from a failing alternator can damage the PCM.<\/li>\n<li style=\"margin:10px 0;line-height:1.65\">Keep all ground connections and wiring harness connectors clean and tight to ensure stable power and signal integrity.<\/li>\n<li style=\"margin:10px 0;line-height:1.65\">Avoid jump-starting the vehicle with a running donor vehicle; use a battery charger or follow proper jump-start procedures to prevent voltage surges.<\/li>\n<li style=\"margin:10px 0;line-height:1.65\">Address any diagnostic trouble codes promptly, especially those related to sensor circuits, to reduce stress on the PCM.<\/li>\n<li style=\"margin:10px 0;line-height:1.65\">Inspect the PCM connector seals and housing for moisture intrusion, which can corrode internal circuits.<\/li>\n<\/ul>\n<\/div>\n<div class=\"info-section\">\n<h2>Frequently Asked Questions<\/h2>\n<h3>How do I know if the PCM in my 2001 Pontiac Grand Am 2.4L needs to be replaced?<\/h3>\n<p>Common signs include a no-start condition, stalling, transmission shifting problems, or a check engine light with internal PCM codes such as P0601. If the scan tool cannot communicate with the PCM, replacement is often necessary. Always verify power and grounds before condemning the module.<\/p>\n<h3>Can I install a used PCM from a salvage yard in my 2001 Pontiac Grand Am?<\/h3>\n<p>A used PCM may work, but it must be programmed with the correct VIN and calibration for your vehicle. The module is VIN-locked and may not function properly without reprogramming. A new or refurbished unit that comes pre-programmed is often a more reliable choice.<\/p>\n<h3>What is involved in the PCM relearn procedure after replacement?<\/h3>\n<p>The relearn procedure takes about 0.5 hours and allows the PCM to adapt to the engine&#8217;s idle and fuel trim parameters. It typically involves a specific driving cycle or scan tool commands. If you purchase a pre-programmed unit from Flagship One, the relearn may still be required to fine-tune operation.<\/p>\n<\/div>\n<div class=\"info-section\">\n<p>When your 2001 Pontiac Grand Am 2.4L PCM fails, you have options: repair the existing module or replace it with a new or refurbished unit. Repair may be possible for some internal faults, but replacement is often more cost-effective and reliable. Flagship One offers refurbished PCMs that are pre-programmed with your vehicle&#8217;s VIN, eliminating the need for a trip to the dealer for programming.<\/p>\n<figure style=\"margin:22px auto;text-align:center;max-width:720px\"><img decoding=\"async\" style=\"max-width:100%;height:auto;border:1px solid #e2e6ec;border-radius:8px\" src=\"https:\/\/www.fs1inc.com\/media\/wysiwyg\/googleshop\/gmtypeA\/gm-pcm-typea-1.jpg\" alt=\"Refurbished VIN-programmed PCM for the 2001 Pontiac Grand Am\" loading=\"lazy\"\/><figcaption style=\"font-size:13px;color:#667085;margin-top:8px\">A refurbished, VIN-programmed replacement PCM for the 2001 Pontiac Grand Am from Flagship One.<\/figcaption><\/figure>\n<p>Flagship One stocks a <a href=\"https:\/\/www.fs1inc.com\/2001-pontiac-grand-am-2-4l-engine-computer-pcm-ecm-ecu-programmed-plug-play.html\"><b>refurbished, VIN-programmed PCM for the 2001 Pontiac Grand Am<\/b><\/a> with a lifetime warranty, free shipping and no core charge. The full <a href=\"https:\/\/www.fs1inc.com\/gm\/pontiac-pcm-ecm-ecu-engine-computer\/grand-am-engine-computers.html\">Pontiac Grand Am module lineup<\/a> covers other engine configurations as well.<\/p>\n<\/div>\n<div class=\"info-section\">\n<h2>Final Thoughts<\/h2>\n<p>The powertrain control module in your 2001 Pontiac Grand Am 2.4L is essential for engine and transmission performance. Recognizing symptoms early and following factory procedures for replacement and programming can restore reliable operation. If you suspect PCM failure, consider a pre-programmed replacement to simplify the repair process.<\/p>\n<\/div>\n<\/div>\n","protected":false},"excerpt":{"rendered":"<p>Symptoms like neutral flare, no 1-2 upshift, or SES light in a 2001 Pontiac Grand Am 2.4L? Caution: only reprogram per GM service bulletins. Learn replacement and programming steps.<\/p>\n","protected":false},"author":1,"featured_media":522447,"comment_status":"open","ping_status":"closed","sticky":false,"template":"elementor_header_footer","format":"standard","meta":{"_acf_changed":false,"footnotes":""},"categories":[258,474],"tags":[277,1571,72],"class_list":["post-534646","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-car","category-pontiac","tag-277","tag-grand-am","tag-pontiac"],"acf":[],"yoast_head":"<!-- This site is optimized with the Yoast SEO plugin v28.0 - https:\/\/yoast.com\/product\/yoast-seo-wordpress\/ -->\n<title>2001 Pontiac Grand Am 2.4L PCM Replacement and Programming - Flagship One Blog<\/title>\n<meta name=\"robots\" content=\"index, follow, max-snippet:-1, max-image-preview:large, max-video-preview:-1\" \/>\n<link rel=\"canonical\" href=\"https:\/\/www.fs1inc.com\/blog\/2001-pontiac-grand-am-pcm-replacement-guide\/\" \/>\n<meta property=\"og:locale\" content=\"en_US\" \/>\n<meta property=\"og:type\" content=\"article\" \/>\n<meta property=\"og:title\" content=\"2001 Pontiac Grand Am 2.4L PCM Replacement and Programming - Flagship One Blog\" \/>\n<meta property=\"og:description\" content=\"Symptoms like neutral flare, no 1-2 upshift, or SES light in a 2001 Pontiac Grand Am 2.4L? Caution: only reprogram per GM service bulletins. Learn replacement and programming steps.\" \/>\n<meta property=\"og:url\" content=\"https:\/\/www.fs1inc.com\/blog\/2001-pontiac-grand-am-pcm-replacement-guide\/\" \/>\n<meta property=\"og:site_name\" content=\"Flagship One Blog\" \/>\n<meta property=\"article:publisher\" content=\"https:\/\/www.facebook.com\/flagshipone\" \/>\n<meta property=\"article:author\" content=\"https:\/\/www.facebook.com\/flagshipone\/\" \/>\n<meta property=\"article:published_time\" content=\"2026-07-17T21:52:54+00:00\" \/>\n<meta property=\"article:modified_time\" content=\"2026-07-19T16:24:21+00:00\" \/>\n<meta property=\"og:image\" content=\"https:\/\/www.fs1inc.com\/blog\/wp-content\/uploads\/2026\/07\/2001-pontiac-grand-am-pcm-location-card.webp\" \/>\n\t<meta property=\"og:image:width\" content=\"1200\" \/>\n\t<meta property=\"og:image:height\" content=\"675\" \/>\n\t<meta property=\"og:image:type\" content=\"image\/webp\" \/>\n<meta name=\"author\" content=\"FlagshipOne\" \/>\n<meta name=\"twitter:card\" content=\"summary_large_image\" \/>\n<meta name=\"twitter:creator\" content=\"@theflagshipone\" \/>\n<meta name=\"twitter:site\" content=\"@theflagshipone\" \/>\n<meta name=\"twitter:label1\" content=\"Written by\" \/>\n\t<meta name=\"twitter:data1\" content=\"FlagshipOne\" \/>\n\t<meta name=\"twitter:label2\" content=\"Est. reading time\" \/>\n\t<meta name=\"twitter:data2\" content=\"8 minutes\" \/>\n<script type=\"application\/ld+json\" class=\"yoast-schema-graph\">{\"@context\":\"https:\\\/\\\/schema.org\",\"@graph\":[{\"@type\":\"Article\",\"@id\":\"https:\\\/\\\/www.fs1inc.com\\\/blog\\\/2001-pontiac-grand-am-pcm-replacement-guide\\\/#article\",\"isPartOf\":{\"@id\":\"https:\\\/\\\/www.fs1inc.com\\\/blog\\\/2001-pontiac-grand-am-pcm-replacement-guide\\\/\"},\"author\":{\"name\":\"FlagshipOne\",\"@id\":\"https:\\\/\\\/www.fs1inc.com\\\/blog\\\/#\\\/schema\\\/person\\\/a3cf463514bd03eb7656953ef8f75700\"},\"headline\":\"2001 Pontiac Grand Am 2.4L PCM Replacement and Programming\",\"datePublished\":\"2026-07-17T21:52:54+00:00\",\"dateModified\":\"2026-07-19T16:24:21+00:00\",\"mainEntityOfPage\":{\"@id\":\"https:\\\/\\\/www.fs1inc.com\\\/blog\\\/2001-pontiac-grand-am-pcm-replacement-guide\\\/\"},\"wordCount\":1606,\"commentCount\":0,\"publisher\":{\"@id\":\"https:\\\/\\\/www.fs1inc.com\\\/blog\\\/#organization\"},\"image\":{\"@id\":\"https:\\\/\\\/www.fs1inc.com\\\/blog\\\/2001-pontiac-grand-am-pcm-replacement-guide\\\/#primaryimage\"},\"thumbnailUrl\":\"https:\\\/\\\/www.fs1inc.com\\\/blog\\\/wp-content\\\/uploads\\\/2026\\\/07\\\/2001-pontiac-grand-am-pcm-location-card.webp\",\"keywords\":[\"2001\",\"Grand Am\",\"Pontiac\"],\"articleSection\":[\"Car\",\"Pontiac\"],\"inLanguage\":\"en-US\",\"potentialAction\":[{\"@type\":\"CommentAction\",\"name\":\"Comment\",\"target\":[\"https:\\\/\\\/www.fs1inc.com\\\/blog\\\/2001-pontiac-grand-am-pcm-replacement-guide\\\/#respond\"]}]},{\"@type\":\"WebPage\",\"@id\":\"https:\\\/\\\/www.fs1inc.com\\\/blog\\\/2001-pontiac-grand-am-pcm-replacement-guide\\\/\",\"url\":\"https:\\\/\\\/www.fs1inc.com\\\/blog\\\/2001-pontiac-grand-am-pcm-replacement-guide\\\/\",\"name\":\"2001 Pontiac Grand Am 2.4L PCM Replacement and Programming - Flagship One Blog\",\"isPartOf\":{\"@id\":\"https:\\\/\\\/www.fs1inc.com\\\/blog\\\/#website\"},\"primaryImageOfPage\":{\"@id\":\"https:\\\/\\\/www.fs1inc.com\\\/blog\\\/2001-pontiac-grand-am-pcm-replacement-guide\\\/#primaryimage\"},\"image\":{\"@id\":\"https:\\\/\\\/www.fs1inc.com\\\/blog\\\/2001-pontiac-grand-am-pcm-replacement-guide\\\/#primaryimage\"},\"thumbnailUrl\":\"https:\\\/\\\/www.fs1inc.com\\\/blog\\\/wp-content\\\/uploads\\\/2026\\\/07\\\/2001-pontiac-grand-am-pcm-location-card.webp\",\"datePublished\":\"2026-07-17T21:52:54+00:00\",\"dateModified\":\"2026-07-19T16:24:21+00:00\",\"breadcrumb\":{\"@id\":\"https:\\\/\\\/www.fs1inc.com\\\/blog\\\/2001-pontiac-grand-am-pcm-replacement-guide\\\/#breadcrumb\"},\"inLanguage\":\"en-US\",\"potentialAction\":[{\"@type\":\"ReadAction\",\"target\":[\"https:\\\/\\\/www.fs1inc.com\\\/blog\\\/2001-pontiac-grand-am-pcm-replacement-guide\\\/\"]}]},{\"@type\":\"ImageObject\",\"inLanguage\":\"en-US\",\"@id\":\"https:\\\/\\\/www.fs1inc.com\\\/blog\\\/2001-pontiac-grand-am-pcm-replacement-guide\\\/#primaryimage\",\"url\":\"https:\\\/\\\/www.fs1inc.com\\\/blog\\\/wp-content\\\/uploads\\\/2026\\\/07\\\/2001-pontiac-grand-am-pcm-location-card.webp\",\"contentUrl\":\"https:\\\/\\\/www.fs1inc.com\\\/blog\\\/wp-content\\\/uploads\\\/2026\\\/07\\\/2001-pontiac-grand-am-pcm-location-card.webp\",\"width\":1200,\"height\":675,\"caption\":\"Typical PCM mounting area on the 2001 Pontiac Grand Am \u2014 reference card\"},{\"@type\":\"BreadcrumbList\",\"@id\":\"https:\\\/\\\/www.fs1inc.com\\\/blog\\\/2001-pontiac-grand-am-pcm-replacement-guide\\\/#breadcrumb\",\"itemListElement\":[{\"@type\":\"ListItem\",\"position\":1,\"name\":\"Home\",\"item\":\"https:\\\/\\\/www.fs1inc.com\\\/blog\\\/\"},{\"@type\":\"ListItem\",\"position\":2,\"name\":\"2001 Pontiac Grand Am 2.4L PCM Replacement and Programming\"}]},{\"@type\":\"WebSite\",\"@id\":\"https:\\\/\\\/www.fs1inc.com\\\/blog\\\/#website\",\"url\":\"https:\\\/\\\/www.fs1inc.com\\\/blog\\\/\",\"name\":\"Flagship One Blog\",\"description\":\"Flagship One Inc. OEM Engine Computers  Control Modules\",\"publisher\":{\"@id\":\"https:\\\/\\\/www.fs1inc.com\\\/blog\\\/#organization\"},\"potentialAction\":[{\"@type\":\"SearchAction\",\"target\":{\"@type\":\"EntryPoint\",\"urlTemplate\":\"https:\\\/\\\/www.fs1inc.com\\\/blog\\\/?s={search_term_string}\"},\"query-input\":{\"@type\":\"PropertyValueSpecification\",\"valueRequired\":true,\"valueName\":\"search_term_string\"}}],\"inLanguage\":\"en-US\"},{\"@type\":\"Organization\",\"@id\":\"https:\\\/\\\/www.fs1inc.com\\\/blog\\\/#organization\",\"name\":\"Flagship One, Inc.\",\"url\":\"https:\\\/\\\/www.fs1inc.com\\\/blog\\\/\",\"logo\":{\"@type\":\"ImageObject\",\"inLanguage\":\"en-US\",\"@id\":\"https:\\\/\\\/www.fs1inc.com\\\/blog\\\/#\\\/schema\\\/logo\\\/image\\\/\",\"url\":\"https:\\\/\\\/www.fs1inc.com\\\/blog\\\/wp-content\\\/uploads\\\/2019\\\/06\\\/web-lg-fs1-logo.png\",\"contentUrl\":\"https:\\\/\\\/www.fs1inc.com\\\/blog\\\/wp-content\\\/uploads\\\/2019\\\/06\\\/web-lg-fs1-logo.png\",\"width\":1341,\"height\":1098,\"caption\":\"Flagship One, Inc.\"},\"image\":{\"@id\":\"https:\\\/\\\/www.fs1inc.com\\\/blog\\\/#\\\/schema\\\/logo\\\/image\\\/\"},\"sameAs\":[\"https:\\\/\\\/www.facebook.com\\\/flagshipone\",\"https:\\\/\\\/x.com\\\/theflagshipone\",\"https:\\\/\\\/www.instagram.com\\\/flagship_one\",\"https:\\\/\\\/www.youtube.com\\\/channel\\\/UC0oyKphffBM2qkJ-gKPmMXw\"]},{\"@type\":\"Person\",\"@id\":\"https:\\\/\\\/www.fs1inc.com\\\/blog\\\/#\\\/schema\\\/person\\\/a3cf463514bd03eb7656953ef8f75700\",\"name\":\"FlagshipOne\",\"image\":{\"@type\":\"ImageObject\",\"inLanguage\":\"en-US\",\"@id\":\"https:\\\/\\\/secure.gravatar.com\\\/avatar\\\/351b81e51993825aea73280c48061a7205fdd2189730ebbdee5d63894c5cebb4?s=96&d=mm&r=g\",\"url\":\"https:\\\/\\\/secure.gravatar.com\\\/avatar\\\/351b81e51993825aea73280c48061a7205fdd2189730ebbdee5d63894c5cebb4?s=96&d=mm&r=g\",\"contentUrl\":\"https:\\\/\\\/secure.gravatar.com\\\/avatar\\\/351b81e51993825aea73280c48061a7205fdd2189730ebbdee5d63894c5cebb4?s=96&d=mm&r=g\",\"caption\":\"FlagshipOne\"},\"description\":\"The world's top supplier of programmed OEM (Original Equipment Manufacturer) Powertrain Control Modules (PCM), Engine Control Modules (ECM), Injection Control Modules (IDM), Body Control Modules (BCM), Transmission Control Modules (TCM), Engine Control Units and all other car control units. With over a decade in the business, we are the most reliable source when it comes to programming services for replacement engine control modules.\",\"sameAs\":[\"https:\\\/\\\/www.fs1inc.com\\\/\",\"https:\\\/\\\/www.facebook.com\\\/flagshipone\\\/\",\"https:\\\/\\\/www.instagram.com\\\/flagship_one\\\/\",\"https:\\\/\\\/www.linkedin.com\\\/company\\\/fs1inc\"],\"url\":\"https:\\\/\\\/www.fs1inc.com\\\/blog\\\/author\\\/flagship1inc\\\/\"}]}<\/script>\n<!-- \/ Yoast SEO plugin. -->","yoast_head_json":{"title":"2001 Pontiac Grand Am 2.4L PCM Replacement and Programming - Flagship One Blog","robots":{"index":"index","follow":"follow","max-snippet":"max-snippet:-1","max-image-preview":"max-image-preview:large","max-video-preview":"max-video-preview:-1"},"canonical":"https:\/\/www.fs1inc.com\/blog\/2001-pontiac-grand-am-pcm-replacement-guide\/","og_locale":"en_US","og_type":"article","og_title":"2001 Pontiac Grand Am 2.4L PCM Replacement and Programming - Flagship One Blog","og_description":"Symptoms like neutral flare, no 1-2 upshift, or SES light in a 2001 Pontiac Grand Am 2.4L? Caution: only reprogram per GM service bulletins. Learn replacement and programming steps.","og_url":"https:\/\/www.fs1inc.com\/blog\/2001-pontiac-grand-am-pcm-replacement-guide\/","og_site_name":"Flagship One Blog","article_publisher":"https:\/\/www.facebook.com\/flagshipone","article_author":"https:\/\/www.facebook.com\/flagshipone\/","article_published_time":"2026-07-17T21:52:54+00:00","article_modified_time":"2026-07-19T16:24:21+00:00","og_image":[{"width":1200,"height":675,"url":"https:\/\/www.fs1inc.com\/blog\/wp-content\/uploads\/2026\/07\/2001-pontiac-grand-am-pcm-location-card.webp","type":"image\/webp"}],"author":"FlagshipOne","twitter_card":"summary_large_image","twitter_creator":"@theflagshipone","twitter_site":"@theflagshipone","twitter_misc":{"Written by":"FlagshipOne","Est. reading time":"8 minutes"},"schema":{"@context":"https:\/\/schema.org","@graph":[{"@type":"Article","@id":"https:\/\/www.fs1inc.com\/blog\/2001-pontiac-grand-am-pcm-replacement-guide\/#article","isPartOf":{"@id":"https:\/\/www.fs1inc.com\/blog\/2001-pontiac-grand-am-pcm-replacement-guide\/"},"author":{"name":"FlagshipOne","@id":"https:\/\/www.fs1inc.com\/blog\/#\/schema\/person\/a3cf463514bd03eb7656953ef8f75700"},"headline":"2001 Pontiac Grand Am 2.4L PCM Replacement and Programming","datePublished":"2026-07-17T21:52:54+00:00","dateModified":"2026-07-19T16:24:21+00:00","mainEntityOfPage":{"@id":"https:\/\/www.fs1inc.com\/blog\/2001-pontiac-grand-am-pcm-replacement-guide\/"},"wordCount":1606,"commentCount":0,"publisher":{"@id":"https:\/\/www.fs1inc.com\/blog\/#organization"},"image":{"@id":"https:\/\/www.fs1inc.com\/blog\/2001-pontiac-grand-am-pcm-replacement-guide\/#primaryimage"},"thumbnailUrl":"https:\/\/www.fs1inc.com\/blog\/wp-content\/uploads\/2026\/07\/2001-pontiac-grand-am-pcm-location-card.webp","keywords":["2001","Grand Am","Pontiac"],"articleSection":["Car","Pontiac"],"inLanguage":"en-US","potentialAction":[{"@type":"CommentAction","name":"Comment","target":["https:\/\/www.fs1inc.com\/blog\/2001-pontiac-grand-am-pcm-replacement-guide\/#respond"]}]},{"@type":"WebPage","@id":"https:\/\/www.fs1inc.com\/blog\/2001-pontiac-grand-am-pcm-replacement-guide\/","url":"https:\/\/www.fs1inc.com\/blog\/2001-pontiac-grand-am-pcm-replacement-guide\/","name":"2001 Pontiac Grand Am 2.4L PCM Replacement and Programming - Flagship One Blog","isPartOf":{"@id":"https:\/\/www.fs1inc.com\/blog\/#website"},"primaryImageOfPage":{"@id":"https:\/\/www.fs1inc.com\/blog\/2001-pontiac-grand-am-pcm-replacement-guide\/#primaryimage"},"image":{"@id":"https:\/\/www.fs1inc.com\/blog\/2001-pontiac-grand-am-pcm-replacement-guide\/#primaryimage"},"thumbnailUrl":"https:\/\/www.fs1inc.com\/blog\/wp-content\/uploads\/2026\/07\/2001-pontiac-grand-am-pcm-location-card.webp","datePublished":"2026-07-17T21:52:54+00:00","dateModified":"2026-07-19T16:24:21+00:00","breadcrumb":{"@id":"https:\/\/www.fs1inc.com\/blog\/2001-pontiac-grand-am-pcm-replacement-guide\/#breadcrumb"},"inLanguage":"en-US","potentialAction":[{"@type":"ReadAction","target":["https:\/\/www.fs1inc.com\/blog\/2001-pontiac-grand-am-pcm-replacement-guide\/"]}]},{"@type":"ImageObject","inLanguage":"en-US","@id":"https:\/\/www.fs1inc.com\/blog\/2001-pontiac-grand-am-pcm-replacement-guide\/#primaryimage","url":"https:\/\/www.fs1inc.com\/blog\/wp-content\/uploads\/2026\/07\/2001-pontiac-grand-am-pcm-location-card.webp","contentUrl":"https:\/\/www.fs1inc.com\/blog\/wp-content\/uploads\/2026\/07\/2001-pontiac-grand-am-pcm-location-card.webp","width":1200,"height":675,"caption":"Typical PCM mounting area on the 2001 Pontiac Grand Am \u2014 reference card"},{"@type":"BreadcrumbList","@id":"https:\/\/www.fs1inc.com\/blog\/2001-pontiac-grand-am-pcm-replacement-guide\/#breadcrumb","itemListElement":[{"@type":"ListItem","position":1,"name":"Home","item":"https:\/\/www.fs1inc.com\/blog\/"},{"@type":"ListItem","position":2,"name":"2001 Pontiac Grand Am 2.4L PCM Replacement and Programming"}]},{"@type":"WebSite","@id":"https:\/\/www.fs1inc.com\/blog\/#website","url":"https:\/\/www.fs1inc.com\/blog\/","name":"Flagship One Blog","description":"Flagship One Inc. OEM Engine Computers  Control Modules","publisher":{"@id":"https:\/\/www.fs1inc.com\/blog\/#organization"},"potentialAction":[{"@type":"SearchAction","target":{"@type":"EntryPoint","urlTemplate":"https:\/\/www.fs1inc.com\/blog\/?s={search_term_string}"},"query-input":{"@type":"PropertyValueSpecification","valueRequired":true,"valueName":"search_term_string"}}],"inLanguage":"en-US"},{"@type":"Organization","@id":"https:\/\/www.fs1inc.com\/blog\/#organization","name":"Flagship One, Inc.","url":"https:\/\/www.fs1inc.com\/blog\/","logo":{"@type":"ImageObject","inLanguage":"en-US","@id":"https:\/\/www.fs1inc.com\/blog\/#\/schema\/logo\/image\/","url":"https:\/\/www.fs1inc.com\/blog\/wp-content\/uploads\/2019\/06\/web-lg-fs1-logo.png","contentUrl":"https:\/\/www.fs1inc.com\/blog\/wp-content\/uploads\/2019\/06\/web-lg-fs1-logo.png","width":1341,"height":1098,"caption":"Flagship One, Inc."},"image":{"@id":"https:\/\/www.fs1inc.com\/blog\/#\/schema\/logo\/image\/"},"sameAs":["https:\/\/www.facebook.com\/flagshipone","https:\/\/x.com\/theflagshipone","https:\/\/www.instagram.com\/flagship_one","https:\/\/www.youtube.com\/channel\/UC0oyKphffBM2qkJ-gKPmMXw"]},{"@type":"Person","@id":"https:\/\/www.fs1inc.com\/blog\/#\/schema\/person\/a3cf463514bd03eb7656953ef8f75700","name":"FlagshipOne","image":{"@type":"ImageObject","inLanguage":"en-US","@id":"https:\/\/secure.gravatar.com\/avatar\/351b81e51993825aea73280c48061a7205fdd2189730ebbdee5d63894c5cebb4?s=96&d=mm&r=g","url":"https:\/\/secure.gravatar.com\/avatar\/351b81e51993825aea73280c48061a7205fdd2189730ebbdee5d63894c5cebb4?s=96&d=mm&r=g","contentUrl":"https:\/\/secure.gravatar.com\/avatar\/351b81e51993825aea73280c48061a7205fdd2189730ebbdee5d63894c5cebb4?s=96&d=mm&r=g","caption":"FlagshipOne"},"description":"The world's top supplier of programmed OEM (Original Equipment Manufacturer) Powertrain Control Modules (PCM), Engine Control Modules (ECM), Injection Control Modules (IDM), Body Control Modules (BCM), Transmission Control Modules (TCM), Engine Control Units and all other car control units. With over a decade in the business, we are the most reliable source when it comes to programming services for replacement engine control modules.","sameAs":["https:\/\/www.fs1inc.com\/","https:\/\/www.facebook.com\/flagshipone\/","https:\/\/www.instagram.com\/flagship_one\/","https:\/\/www.linkedin.com\/company\/fs1inc"],"url":"https:\/\/www.fs1inc.com\/blog\/author\/flagship1inc\/"}]}},"_links":{"self":[{"href":"https:\/\/www.fs1inc.com\/blog\/wp-json\/wp\/v2\/posts\/534646","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.fs1inc.com\/blog\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/www.fs1inc.com\/blog\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/www.fs1inc.com\/blog\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/www.fs1inc.com\/blog\/wp-json\/wp\/v2\/comments?post=534646"}],"version-history":[{"count":2,"href":"https:\/\/www.fs1inc.com\/blog\/wp-json\/wp\/v2\/posts\/534646\/revisions"}],"predecessor-version":[{"id":538728,"href":"https:\/\/www.fs1inc.com\/blog\/wp-json\/wp\/v2\/posts\/534646\/revisions\/538728"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/www.fs1inc.com\/blog\/wp-json\/wp\/v2\/media\/522447"}],"wp:attachment":[{"href":"https:\/\/www.fs1inc.com\/blog\/wp-json\/wp\/v2\/media?parent=534646"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/www.fs1inc.com\/blog\/wp-json\/wp\/v2\/categories?post=534646"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/www.fs1inc.com\/blog\/wp-json\/wp\/v2\/tags?post=534646"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}